1252.()程序段N10L51P2的含义是连续调用子程序L51"2次(SIEMENS系统)。()"
https://www.shititong.cn/cha-kan/shiti/0005f002-2c0b-f418-c0f5-18fb755e8806.html
点击查看答案
991.()几个轴联动时不能同时到达终点的原因是几个轴的误差不一致。()
https://www.shititong.cn/cha-kan/shiti/0005f002-2c0b-d8c0-c0f5-18fb755e8815.html
点击查看答案
50.在使用镜像加工功能时,第I象限的顺时针圆弧,到了其他象限为( )(FANUC系统)。
A. II,III为顺圆,IV为逆圆
B. II,IV为顺圆,III为逆圆
C. II、IV为逆圆,III为顺圆
D. II,III为逆圆,IV为顺圆
https://www.shititong.cn/cha-kan/shiti/0005f002-2a7f-ca20-c0f5-18fb755e8818.html
点击查看答案
1030.()球头铣刀刀位点是球顶点。()
https://www.shititong.cn/cha-kan/shiti/0005f002-2c0b-dca8-c0f5-18fb755e8815.html
点击查看答案
195.( )铣削加工中最先确定的用量是()。
https://www.shititong.cn/cha-kan/shiti/0005f002-2a7f-9b40-c0f5-18fb755e881d.html
点击查看答案
111.公差与配合的基本规定中,H7中的符号H代表基孔制,其上偏差为正,下偏差为( )。
A. 负值
B. 正值
C. 配合间隙值
D. 零
https://www.shititong.cn/cha-kan/shiti/0005f002-2a7f-d1f0-c0f5-18fb755e8809.html
点击查看答案
40.偏心夹紧装置使用在( )的场合。
A. 要求夹紧力大
B. 不要求夹紧力大
C. 加工中振动大
D. 加工中振动小
https://www.shititong.cn/cha-kan/shiti/0005f002-2a7f-ca20-c0f5-18fb755e880e.html
点击查看答案
1289.()程序段N30WHILE#2LE10;…;N60ENDW;表示如果#2中的值小于或等于10,将循环执行N30段后至N60之间的程序段(华中系统)。()
https://www.shititong.cn/cha-kan/shiti/0005f002-2c0b-f800-c0f5-18fb755e8804.html
点击查看答案
1154.()循环语句WHILE[条件表达式]"中,条件表达式的赋值一定是常量(华中系统)。()
https://www.shititong.cn/cha-kan/shiti/0005f002-2c0b-e860-c0f5-18fb755e881a.html
点击查看答案
267.()工序尺寸公差一般按该工序加工的()来选定。
A. 经济加工精度
B. 最高加工精度
C. 最低加工精度
D. 平均加工精度
https://www.shititong.cn/cha-kan/shiti/0005f002-2a7f-a310-c0f5-18fb755e881c.html
点击查看答案