A、 处理边缘锋利的零件时要戴手套。
B、 处理边缘有凹痕的零件时要戴手套。
C、 当接触边缘有锯齿的零件时要戴手套。
答案:C
A、 处理边缘锋利的零件时要戴手套。
B、 处理边缘有凹痕的零件时要戴手套。
C、 当接触边缘有锯齿的零件时要戴手套。
答案:C
A. 因 CAP 是针对特定的零件或部件,可得知检查将包括对零件和设备周围区域的观察和评估
B. 由于 CAP 是针对特定的零件或部件,可推测出检查将包括对零件和设备周围区域的观察和评估
C. 只要 CAP 是针对特定的零件或部件,就意味着检查将包括对零件和设备周围区域的观察和评估
A. 因 CAP 是针对特定的零件或部件,可得知检查将包括对零件和设备周围区域的观察和评估
B. 由于 CAP 是针对特定的零件或部件,可推测出检查将包括对零件和设备周围区域的观察和评估
C. 只要 CAP 是针对特定的零件或部件,就意味着检查将包括对零件和设备周围区域的观察和评估
A. Access doors and panels within the area are recognized by the number of the area and two or three letter suffix.
B. The area number and a postfix with two or three letters identifies the access doors and panels in an area.
C. The identification of the access panels and doors is accomplished by the zone number suffix.
A. The airflow then goes along the above and bottom surfaces of the aileron.
B. The air value then goes through the cover and bottom surfaces of the flank.
C. The airflow then goes along the top and bottom surfaces of the slats.
A. A separate document should be prepared for FAA approved airworthiness limitations which are excluded in the primary maintenance manual.
B. FAA approved airworthiness limitations shall be prepared as a separate document for inclusion in the principal maintenance manual.
C. FAA approved airworthiness limitations must be contained as an integrated documentation for inclusion in the main maintenance manual.
A. Before removing and disposing the seal ring , cut and dispose the fuse that secures the oil drain plug to the fuel cooled integral drive generator oil cooler.
B. Before removing and retaining the seal ring, cut and retaining the wire that secures the oil fill plug to the fuel cooled integral drive generator oil cooler.
C. Before removing and discarding the sealing ring, cut and discard the wire which safeties the oil cooler.
A. 主题标题应与本规范中使用的示例相同,或实质上等同于本规范中使用的示例,除非因飞机型号的设计或运行特 点而不适用。
B. 除了因飞机种类的设计或操作方式不适用的情况,主题标题应与本规范中使用的示例一致或本质相似。
C. 除了因飞机类型的设计或运行方式不适用的情况,主题标题应与本规范中使用的示例一致或近似。
A. Obey the following procedure if the manufacturer provides you different instructions
B. If the manufacturer instructs you differently, the following procedure should be ignored
C. If the man ufacturer's instructions are different from the following procedure, obey the following procedure
A. Throughout the manual, the coding used is the same as in other systems;
B. The same coding for each individual system shall be used throughout the manual;
C. The same coding shall be used in the manual;
A. 用设置开关以重置运行时间。
B. 用重置按钮以重置运行时间。
C. 用重置按钮以重置格林威治时间。