A、 When you need to understand a schematic diagram,use arrows to indicate flow orientation.
B、 Arrows shall be used to signify flow direction when needed to realize the schematic form.
C、 When need to comprehend the chart,you should use arrows point to the direction.
答案:A
A、 When you need to understand a schematic diagram,use arrows to indicate flow orientation.
B、 Arrows shall be used to signify flow direction when needed to realize the schematic form.
C、 When need to comprehend the chart,you should use arrows point to the direction.
答案:A
A. If you must add a page after the ahead printing,the page should have the number of the preceding page and an alphabetic suffix.
B. In the event a page must be added pursuant to the original printing,the page shall carry the number of the preceding page with a letter postfix added.
C. If you must add pages after the individual printing,then the page should contain the serial number of the preceding page,and add a suffix letters.
A. You do not need to give the return processes in entirety unless you heed to comprehend the system.
B. Unless you need to comprehend the system,do not need to fully show the return lines.
C. Return lines need not be shown completely if the system need not be realized.
A. 在器。支架反向的位置上放置适配
B. 放置适配器的位置背向支架。
C. 将适配器紧靠在支架上。
A. 所得数据用于确定是否应考•虑将部件并入CAP。
B. 数据结果用于确定是否应考虑将部件并入CAP。
C. 最终数据用于确定是否应考虑将部件移除CAP。
A. If there is hum from the loudspeaker,don't adjust the potentiometer.
B. Adjust the potentiometer unless hear a hum from the loudspeaker.
C. Adjust the potentiometer until the loudspeaker no longer hums.
A. 无线电高度表在初始爬升时确定飞机距离地面的高度,确定飞机是否进入进近和着陆阶段。
B. 无线电高度表在初始爬升、进近和着陆阶段确定飞机的地形和高度。
C. 无线电高度表在初始爬升、进近和着陆阶段确定飞机距离地面的高度。
A. 制造商应将制造商发布的类型服务信息以及为获取此类信息而联系的办公室或部门的描述包括在内,以便飞机可以按照发布的最新信息进行维护。
B. 制造商应包括其发布的服务信息的类型说明,以及能提供此类信息的办公室或部门,从而按照最终 发布的信息维护飞机。
C. 制造商应将其发布的服务信息的类型包括在内,以及能提供此类信息的办公室或部门,从而按照最终发布的信息维护飞机。
A. Nomenclature shall be similar throughout all technical data obtained by the Customer.
B. Nomenclature shall be consistent throughout all technical data given to the Customer.
C. Nomenclature must be similar throughout all technical data provided to the Customer.
A. A value of 2 mm is permitted.
B. A value of 2 mm is rejected.
C. A value of 2 mm is unacceptable。
A. 如果不正确跟进操作程序、检查、修理或维护程序,可能导致人员受伤。
B. 如果没有紧跟操作程序、检查、修理或维护程序,可能导致人员伤亡。
C. 如果不正确遵循操作程序、检查、修理或维护程序,可能导致人员伤亡。