41.机床主轴箱内一般采用()。
A. 溅油润滑
B. 针阀式注油油杯润滑
C. 自动定时润滑
D. 手工定时润滑
https://www.shititong.cn/cha-kan/shiti/0005e6cc-0559-4a80-c017-654bab5e0514.html
点击查看答案
73.()相同切削条件下,车孔时的切削用量应比车外圆低一些。
https://www.shititong.cn/cha-kan/shiti/0005e6cc-0709-4858-c017-654bab5e051f.html
点击查看答案
139.()量块的上、下测量面精度高且表面粗糙度值小,每块量块上都标有基本尺寸。
https://www.shititong.cn/cha-kan/shiti/0005e6cc-0709-5028-c017-654bab5e051d.html
点击查看答案
431.对偏差与公差的关系,下列说法正确的是:()。
A. 上偏差越大,公差越大
B. 上、下偏差越大,公差越大
C. 上、下偏差之差越大,公差越大
D. 上、下偏差之差的绝对值越大,公差越大
https://www.shititong.cn/cha-kan/shiti/0005e6cc-0559-7578-c017-654bab5e0521.html
点击查看答案
47.()浇注切削液能冲走在切削过程中留下的细屑或磨粒,从而起到清洗、防止刮伤加工表面和机床导轨面的作用。
https://www.shititong.cn/cha-kan/shiti/0005e6cc-0709-4858-c017-654bab5e0505.html
点击查看答案
480.检验尾座套筒锥孔时,使用()测量。
A. 锥度塞规
B. 万能角度尺
C. 样板
D. 锥度套规
https://www.shititong.cn/cha-kan/shiti/0005e6cc-0559-7d48-c017-654bab5e050c.html
点击查看答案
42.()刀具的前角越大时切削刃越锋利,但是刀具的强度越低。
https://www.shititong.cn/cha-kan/shiti/0005e6cc-0709-4858-c017-654bab5e0500.html
点击查看答案
371.()精车时,刃倾角应取负值。
https://www.shititong.cn/cha-kan/shiti/0005e6cc-0709-6b80-c017-654bab5e0513.html
点击查看答案
287.()工艺尺寸链计算是基准位移误差计算的一种科学方法。
https://www.shititong.cn/cha-kan/shiti/0005e6cc-0709-63b0-c017-654bab5e0505.html
点击查看答案
248.细长轴的刚性很差,在切削力、重力和离心力的作用下会使工件弯曲变形,车削中极易产生()。
A. 表面不光滑
B. 振动
C. 加工精度低
D. 加工效率低
https://www.shititong.cn/cha-kan/shiti/0005e6cc-0559-61f0-c017-654bab5e0517.html
点击查看答案