20、手用工具不应放在工作台边缘是因为( )。
A. 取用不方便
B. 会造成工作台超过负荷
C. 工具易于坠落伤人
https://www.shititong.cn/cha-kan/shiti/0005b4c1-3210-7b30-c039-649e1644b106.html
点击查看答案
75.当零件所有表面具有相同的表面粗糙度要求时,可在图样的( )标注。
A. 左上角
B. 右上角
C. 空白处
D. 任何地方
https://www.shititong.cn/cha-kan/shiti/0005b4c1-2ffd-2b90-c039-649e1644b10d.html
点击查看答案
18、必需品的作用是( )
A. 增大作业的空间
B. 减少库存,节约资金。
C. 减少碰撞,保障安全
D. 消除混料差错
https://www.shititong.cn/cha-kan/shiti/0005b4c1-3210-5bf0-c039-649e1644b100.html
点击查看答案
83.锉刀放入工具箱时,不可与其他工具堆放,也不可与其他锉刀重叠堆放,以免( )。
A. 损坏锉齿
B. 变形
C. 损坏其它工具
D. 不好寻找
https://www.shititong.cn/cha-kan/shiti/0005b4c1-2ffd-2b90-c039-649e1644b115.html
点击查看答案
69.合理调整轴承间隙,可保证轴承寿命,提高( )。
A. 润滑
B. 速度
C. 磨损
D. 旋转精度
https://www.shititong.cn/cha-kan/shiti/0005b4c1-2ffd-2b90-c039-649e1644b107.html
点击查看答案
4、室温高于摄氏( )度,相对湿度超过( )的作业场所,称为高温作业场所。
A. 30℃,80%
B. 35℃,80%
C. 30C,.85%
https://www.shititong.cn/cha-kan/shiti/0005b4c1-3210-5bf0-c039-649e1644b106.html
点击查看答案
8.工件在夹具中定位时,在工件底平面均布三个支承点,限制了三个自由度,这个面称( )。
A. 止动基准面
B. 工艺基准
C. 主要基准
D. 加工基准
https://www.shititong.cn/cha-kan/shiti/0005b4c1-2ffc-ed10-c039-649e1644b11c.html
点击查看答案
8、单次事假不得超过( )天?一年内事假累计不得超过( )天?
A. 3天
B. 5天
C. 30天
D. 60天
https://www.shititong.cn/cha-kan/shiti/0005b4c1-3210-4098-c039-649e1644b104.html
点击查看答案
16.参考点选的不同,电路中各点( )也不同。
https://www.shititong.cn/cha-kan/shiti/0005b4c1-2ffc-ed10-c039-649e1644b124.html
点击查看答案
107.机床精度检验时,由丝杠所产生的螺距累积误差,当Da>2000时在任意60mm测量长度内允差值为( )mm。
A. 0.01
B. 0.015
C. 0.02
D. 0.025
https://www.shititong.cn/cha-kan/shiti/0005b4c1-2ffd-4ad0-c039-649e1644b103.html
点击查看答案