A、 Move the IDG forward and outboard until it is away from the accessory gearbox, QAD ring and power plant.
B、 Move the IDG towards the forward position until the input shaft is away from the accessary gearbox and QAD ring, then move the IDG towards outboard and free of the power plant.
C、 After moving the IDG towards the forward position, then it is free of the accessary gearbox, QAD and the power plant.
答案:B
A、 Move the IDG forward and outboard until it is away from the accessory gearbox, QAD ring and power plant.
B、 Move the IDG towards the forward position until the input shaft is away from the accessary gearbox and QAD ring, then move the IDG towards outboard and free of the power plant.
C、 After moving the IDG towards the forward position, then it is free of the accessary gearbox, QAD and the power plant.
答案:B
A. 描述飞机地面控制时,应描述飞行员如何通过机械方式控制前轮或后轮。
B. 描述地面操作时,应描述飞行员如何机械地操作前轮或后轮。
C. 描述地面操纵时,应描述飞行员如何机械操纵鼻轮或后轮。
A. 齿轮箱部分包括齿轮、曲柄、密封件、油箱、冷却器等。
B. 齿轮箱部分包括叶轮、轴、密封件、油泵、冷却器等。
C. 齿轮箱部分包括齿轮、轴、密封件、油泵、冷却器等。
A. 松散接头会造成损伤。
B. 错误连接会造成损伤。
C. 损伤的原因是松散连接。
A. 通常,希望下面的章排列好,所有手册中的故障被统一推断出并最大范围实施。
B. 一般而言,要求在手册适用的最大程度统一地遵循以下章的布局和划分。
C. 总的来说,所有手册中随后的章的安排和分类应该遵循一致性和最大可行性。
A. The condenser decreases the temperature of the air in the air conditioning pack to below the dew point, changing water vapor into liquid.
B. The cooler lowers the air temperature to the boiling point in the air conditioning module, which can transfer the steam into water.
C. The evaporator turns steam into liquid by reducing the temperature of the air in the air conditioning pack to the evaporating point.
A. 生产商编写的维修手册必须参考本规范中包含的所有材料的格式、字体和展示方法。
B. 本手册中包含的规范可以指导厂家编写维修手册,包括所有规章书写格式和展示方法。
C. 本规范中包含的规则应作为制造商编写的维修手册中包含的所有材料的格式、样式和展示方法的指南。
A. Make sure that the quality of fuel in the reservoir is not more than 500 liters.
B. Make sure that the quantity of fuel in the tank is not more than 500 liters.
C. Make sure that the quality of oil in the tank is not more than 500 liters.
A. 如果轮胎温度升高超过177度,核心机的易熔喷嘴爆破,会爆胎。
B. 如果轮胎温度升高到177度以上,熔断器中心熔化,机轮破损。
C. 如果机轮温度升高到177度以上,易熔塞中心熔化,轮胎会漏气。
A. 残留在零件上的溶剂会导致腐蚀。
B. 残留在零件上的油液会导致腐蚀。
C. 残留在零件上的溶剂会导致穿孔。
A. 注意:当您取出探头时,不要让它们相互接触。
B. 警告:取出探头时,不要让它们相互接触。
C. 注意:当您取出指针时,不要让它们相互接触。