A、 如果在初始印刷版之后必须添加一页，则给添加的页面使用带字母后缀的前一页页码(例如，第1-6A页、1-6B页等)。
B、 如果在最终印刷版之后必须添加一页，则给添加的页面使用带字母前缀的后一页页码(例如，第1-6A页、1-6B页等)。
C、 如果在初始印刷版之后必须删除一页，则给删除的页面装进信件并使用带前缀的前一页页码(例如，第1-6A页、1-6B页等)。
答案：A
A、 如果在初始印刷版之后必须添加一页，则给添加的页面使用带字母后缀的前一页页码(例如，第1-6A页、1-6B页等)。
B、 如果在最终印刷版之后必须添加一页，则给添加的页面使用带字母前缀的后一页页码(例如，第1-6A页、1-6B页等)。
C、 如果在初始印刷版之后必须删除一页，则给删除的页面装进信件并使用带前缀的前一页页码(例如，第1-6A页、1-6B页等)。
答案：A
A. If a symbol or device is established for a valve or control, it shall be used for this type of unit throughout the manual. The symbols used should be shown and identified in a legend block on the schematic diagram.
B. If a symbol or device has been set up to a valve or control, the equipment type will be referred to as this symbol or device throughout the manual. The legend block in the diagram displays or identifies symbols or device.
C. If a symbol or design is specified for a valve or control, this type of device is used throughout the section of the manual. The symbols used can be found and identified in the legend block of the schematic.
A. If your decision is not to change the unit, monitor its temperature at least 15 rotations.
B. If you decide not to renew the unit, supervise its temperature at least 15 periods.
C. If your decision is not to replace the unit, monitor its temperature for a minimum of 15 cycles.
A. The aim of STE is that readers all over the world can easily understand the technical texts and that writers who are responsible for preparing technical texts know how to prepare them in a easy method.
B. The objective of STE is to provide writers with general principles on how to prepare technical documents in a clear, simple and distinct manner that readers all over the world can easily understand.
C. The function of STE is to describe how to prepare technical texts in a easy, clear and specific way and to allow readers all over the world to understand difficultly.
A. If you find damaged lines, restore them.
B. If you find loosen cables, fix them.
C. If you find broken wires, repair them.
A. The localizer beam is aligned with the centerline of the runway.
B. The localizer way is misaligned with the centerline of the runway.
C. The localizer course is aligned with the centerline of the runway.
A. The autothrust system is in but not in operation.
B. The autothrust system is on but not in operation.
C. The autothrust system is out but not in operation.
A. Only number CAP pages that contain one chapter in sequence and identify the chapters.
B. Number the pages of CAPs containing only one section in sequence with section identification.
C. For the CAP pages that contain only a chapter in sequence, mark the chapters.
A. 飞机审定条件包括：一台发动机不工作并处于风车状态（或对于安装自动顺桨装置的飞机，已顺桨），朝向工作发动机一侧倾斜不超过5度，工作发动机处于起飞功率，起落架收上，襟翼在起飞位置，以及最临界重心位置。
B. 飞机的审定条件包括：一个发动机停车，有风动（或在有自动羽化装置的飞机上，已羽化）朝向工作发动机的倾斜度小于5度，起落架升起，襟翼处于起飞状态，以及最不利的重量。
C. 飞机的审定条件包括：一个发动机停止工作，有风动（已在飞机上调为自动顺桨模式）朝向工作发动机的倾斜度大于5度，起落架升起，襟翼处于起飞状态，以及重心处于临界位置。
A. If the error is more than 3 degrees, calibrate the glide slope.
B. If the error is more than 3 degrees, calibrate the compass.
C. If the error is more than 3 degrees, calibrate the gyroscope.
A. Make the attitude of the valves the same.
B. Make the positions of the valves agree.
C. Make the altitude of the valves agree.
